欢迎您访问程序员文章站本站旨在为大家提供分享程序员计算机编程知识!
您现在的位置是: 首页  >  IT编程

基于redis集群设置密码的实例

程序员文章站 2023-02-20 19:33:06
注意事项: 1.如果是使用redis-trib.rb工具构建集群,集群构建完成前不要配置密码,集群构建完毕再通过config set + config rewrite命令...

注意事项:

1.如果是使用redis-trib.rb工具构建集群,集群构建完成前不要配置密码,集群构建完毕再通过config set + config rewrite命令逐个机器设置密码

2.如果对集群设置密码,那么requirepass和masterauth都需要设置,否则发生主从切换时,就会遇到授权问题,可以模拟并观察日志

3.各个节点的密码都必须一致,否则redirected就会失败

config set masterauth abc 
config set requirepass abc 
config rewrite 

测试版本:

redis3.0.7

测试环境:

centos7

集群规模:

3主3从

集群构建成功前的redis配置:

port 8000 
cluster-enabled yes 
cluster-config-file "nodes-8000.conf" 
cluster-node-timeout 15000 
dir "/opt/redisdata" 
appendonly yes 
appendfilename "appendonly-8000.aof" 
logfile "/opt/redisdata/8000.log" 
daemonize yes 
pidfile "/var/run/redis-8000.pid" 
dbfilename "dump-8000.rdb" 
cluster-require-full-coverage no 

集群构建成功后的redis配置:

port 8004 
cluster-enabled yes 
cluster-config-file "nodes-8004.conf" 
cluster-node-timeout 15000 
dir "/opt/redisdata" 
appendonly yes 
appendfilename "appendonly-8004.aof" 
logfile "/opt/redisdata/8004.log" 
daemonize yes 
pidfile "/var/run/redis-8004.pid" 
dbfilename "dump-8004.rdb" 
cluster-require-full-coverage no 
# generated by config rewrite 
requirepass "abc" 
masterauth "abc" 

测试:

1.8002是主,8005是8002的从,现在要kill掉8002模拟主从切换

基于redis集群设置密码的实例

2.查看8005的日志,8005最终被选举成新的master

21227:s 14 jun 07:28:49.343 # connection with master lost.
21227:s 14 jun 07:28:49.343 * caching the disconnected master state.
21227:s 14 jun 07:28:49.433 * connecting to master 127.0.0.1:8002
21227:s 14 jun 07:28:49.433 * master <-> slave sync started
21227:s 14 jun 07:28:49.434 # error condition on socket for sync: connection refused
21227:s 14 jun 07:28:50.437 * connecting to master 127.0.0.1:8002

21227:s 14 jun 07:29:06.205 # start of election delayed for 564 milliseconds (rank #0, offset 337).
21227:s 14 jun 07:29:06.507 * connecting to master 127.0.0.1:8002
21227:s 14 jun 07:29:06.507 * master <-> slave sync started
21227:s 14 jun 07:29:06.507 # error condition on socket for sync: connection refused
21227:s 14 jun 07:29:06.808 # starting a failover election for epoch 10.
21227:s 14 jun 07:29:06.810 # failover election won: i'm the new master.
21227:s 14 jun 07:29:06.810 # configepoch set to 10 after successful failover
21227:m 14 jun 07:29:06.810 * discarding previously cached master state.

3.再次启动8002,查看8005的日志,8002已经变成8005的slave

21227:m 14 jun 07:32:53.511 * slave 127.0.0.1:8002 asks for synchronization
21227:m 14 jun 07:32:53.511 * full resync requested by slave 127.0.0.1:8002
21227:m 14 jun 07:32:53.511 * starting bgsave for sync with target: disk
21227:m 14 jun 07:32:53.511 * background saving started by pid 21613
21613:c 14 jun 07:32:53.513 * db saved on disk
21613:c 14 jun 07:32:53.513 * rdb: 0 mb of memory used by copy-on-write
21227:m 14 jun 07:32:53.612 * background saving terminated with success
21227:m 14 jun 07:32:53.612 * synchronization with slave 127.0.0.1:8002 succeeded

4.简单测试了get set命令,正常

以上这篇基于redis集群设置密码的实例就是小编分享给大家的全部内容了,希望能给大家一个参考,也希望大家多多支持。